Audio Authority SCP-11 Manuel d'utilisateur

User’s ManualControl Panel for Use With System Switchers68-511-01 Rev. C11 08SCP 250PRELIMINARYFront cover

SCP 250 • Installation and OperationInstallation and Operation2-2Installation OverviewTo install and set up an SCP control panel, follow these steps:1

SCP 250 • Installation and Operation 2-31. Cut out the center portion of the template. Cut up to the dashed line if using an electrical box, or cut

SCP 250 • Installation and OperationInstallation and Operation, cont’d2-46. Exposed cable shields (braids or foil) are potential sources of short cir

SCP 250 • Installation and Operation 2-5c DIP switches — Set these switches to indicate what model of system switcher the SCP is attached to.1, 2, 3

SCP 250 • Installation and OperationInstallation and Operation, cont’d2-6Wire both ends of the cable identically (pin A to pin A, pin B to pin B, etc.

SCP 250 • Installation and Operation 2-7the switcher. The illustration below shows several SCPs connected to a System 7SC switcher in a typical daisy

SCP 250 • Installation and OperationInstallation and Operation, cont’d2-8Front Panel Features and OperationSCP 250IR DISPLAY AUDIOVOLUMEPOWER MUTEMODE

SCP 250 • Installation and Operation 2-9c IR signal pickup device — Like the IR signal pickup device on the switcher, this receives commands from the

SCP 250 • Installation and OperationInstallation and Operation, cont’d2-10identically at both ends of the cable and that the faceplate is connected to

SCP 250AAppendix ASpecifications, Part Numbers, Template, LabelsSpecificationsPart NumbersTemplateLabeling Buttons on the SCP

Precautions This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with

SCP 250 • Specications, Part Numbers, Template, LabelsSpecifications, Part Numbers, Template, LabelsA-2SpecificationsControl/remote — control panelsIR

SCP 250 • Specications, Part Numbers, Template, Labels A-3Part NumbersIncluded partsThese items are included in each order for an SCP 250:Included pa

SCP 250 • Specications, Part Numbers, Template, LabelsSpecifications, Part Numbers, Template, LabelsA-4N Rotate the template 90° to install the SCP i

SCP 250 • Specications, Part Numbers, Template, Labels A-5Labeling Buttons on the SCPThe SCP 250 has translucent panels (“windows”) behind which cust

SCP 250 • Specications, Part Numbers, Template, LabelsSpecifications, Part Numbers, Template, LabelsA-6For information about using the program, you ca

SCP 250 • Specications, Part Numbers, Template, Labels A-7ROOM 1For use with a System 7SC switcherFor use with a System 5cr Plus switcherROOM 24123 7

SCP 250 • Specications, Part Numbers, Template, LabelsSpecifications, Part Numbers, Template, LabelsA-8

Extron’s WarrantyExtron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of pu

© 2008 Extron Electronics. All rights reserved.Extron USA - West Headquarters+800.633.9876Inside USA / Canada Only+1.714.491.1500+1.714.491.1517 FAX

SCP 250 • Safety and Compliances 安全须知 • 中文这个符号提示用户该设备用户手册中有重要的操作和维护说明。这个符号警告用户该设备机壳内有暴露的危险电压，有触电危险。注意阅读说明书 • 用户使用该设备前必须阅读并理解所有安全和使用说明。保存说明书 • 用户应保存安全

SCP 250 • Safety and Compliances

iSCP 250 • Table of Contents Table of Contents68-511-01 C11 08All trademarks mentioned in this manual are the properties of their respective owners.C

iiSCP 250 • Table of ContentsTable of Contents, cont’d

SCP 2501Chapter OneIntroductionAbout the SCP 250Features

SCP 250 • IntroductionIntroduction1-2About the SCP 250The Extron SCP 250 is a hard wired remote control panel for use with Extron system switchers. R

SCP 2502Chapter TwoInstallation and OperationInstallation OverviewPreparing the Site, Installing the Electrical BoxRear Panel Connectors and SwitchesC